SPINS Tutorial

This page is currently under construction

If you come across this page while it is under construction and have questions, email Tim (tghill@edu.uwaterloo.ca) and Andrew (a2grace@uwaterloo.ca).

This is a tutorial for getting up to speed with SPINS using the case mode1_mode2. The first part of the tutorial discusses running the case with the default parameters, some basic analysis tools and techniques, and manually changing parameters. The second part of the tutorial explores more parameter combinations using Matlab driver scripts to automate the workflow. The final part using a Matlab script spins_refinement.m to interpolate an existing SPINS output onto a finer grid and restart SPINS at higher resolution.

You must first have followed the instructions to install SPINS and compile the case file.

Part 1: Getting familiar with SPINS

Run

Transfer the executable (mode1_mode2.x) and the configuration file (spins.conf) into a clean directory.

Run simulation by executing mpirun -np 4 ./mode1_mode2.x on the command line, or submit the job to the queue on a Compute Canada system with a submit script (see submitting jobs to Graham).

This will create two types of files

1. Output files
   • These are of the form rho.3 where the name (rho) is the variable and the extension is the output number

   - For example rho.3 is the density field at output number 3. Zero-indexing is used, so this is the 4th density file

   • Since these can be memory expensive, they are created relatively infrequently
2. Diagnostic files
   • These will generally be text files and contain information about the simulation
   • Matlab plotters for the diagnostic files are found in the SPINSmatlab toolbox (preinstalled on boogaloo).

Diagnostic Files
File	Optional	Matlab plotter	Description
diagnostics.txt	No	plot_diagnos	High temporal resolution information about the simulation (occurs at every time step). Examples include: KE, max velocity, energy budget terms, simulation timings.
stresses_top.txt and/or stresses_bottom.txt	Yes	plot_stress	Surface forces and surface stress extrema at the top/bottom surfaces. Only applicable if no slip boundary condition is used.
plot_times.txt	No	plot_diagnos	Explicit statement of the time associated with each output. Also gives the time to write output files.

Analyze

Matlab and Python are the primary languages used for analyzing SPINS simulations. These are great for computation of quantities specific to your study. The Python (SPINSpy) and Matlab (SPINSmatlab) packages contain much of the important tools for each language. Three dimensional visualization should use Paraview or VisIt (see Visualization).

Here, we will use Matlab to make a simple plot of the density field. We assume that the SPINSmatlab package is on your path (as is the case for boogaloo).

1. gdpar = spins_gridparams(); split_gdpar
   • This reads in the grid and parameters and places them in a structure (gdpar). split_gdpar separates the two sub-structures into the structures par and gd, which are the parameters and grid, respectively.
   • par contains information from spins.conf in addition to further simulation parameters
   • gd contains the grid. x,y,z grids can be extracted with gd.x, gd.y, or gd.z
   • The default setting is that the grid is unmapped and vector grids are produced, to get the full grid use gdpar = spins_gridparams('FastFull'); or gdpar = spins_gridparams('Full');
2. spins_plot2d('rho',0);
   • First argument is the field to plot
   • Second argument is the output number. The simulation time can also be specified in this argument as a string. spins_plot2d('rho','2'); will plot the simulation at the closest output to t=2s. Many optional arguments exist (type help spins_plot2d for more options).

To read an individual file: u = spins_reader('u',10);

Restart

Should you need to restart the simulation (due to expenditure of allocated time, require more time, a node failure, or otherwise) simply change the restart flags in the configuration file.

The simplest change is to set

restart = true
restart_time = 5.5
restart_sequence = 11

where the simulation will restart at output 11 which corresponds to t=5.5s. These numbers can be found in the last row of plot_times.txt.

SPINS also has an automatic safety dump if the allocated time is close to expiring (See automatically specify the runtime for more info). In this case, if the safety write was done successfully then you only need to set

restart_from_dump = true

Change

If after analyzing the simulation you realize that you wanted to change a parameter (it wasn't quite right), then you only need to change the parameter in the configuration file (as opposed to older editions of SPINS where you'd need to recompile the entire code).

Here is a description of the problem parameters:

 --delta_rho     arg   Density difference between upper and lower layers (as a percentage of rho_0)
 --pyc_loc       arg   Pycnocline location
 --h_halfwidth   arg   Pycnocline half-width
 --delta_x       arg   Horizontal transition half-width
 --H2            arg   Height of mixed region (mode-2) - sets mode-2 wave amplitude
 --H1            arg   Heigth of mixed region (mode-1) - sets mode-1 wave amplitude
 --L1            arg   Length of region 1 (mode-2)
 --L2            arg   Length of region 2 (mode-1)
 --dye1_loc      arg   Location of dye 1
 --dye2_loc      arg   Location of dye 2
 --dye1_width    arg   Width of dye 1
 --dye2_width    arg   Width of dye 2
 --dye_halfwidth arg   Sharpness of the dye transition
 --enable_tracer       Enable evolution of second tracers

If you run the simulation in the same directory, remember to clear all simulation files (output and diagnostic files).

Only Mode-1 ISW

To change the simulation to only have the left mode-1 ISW change spins.conf to have:

H2 = 0.0

This will set the mode-2 amplitude to zero.

Only Mode-2 ISW

To change the simulation to only have the right mode-2 ISW change spins.conf to have:

H1 = 0.0

This will set the mode-1 amplitude to zero.

Gravity Current

To change the simulation to have a rightward moving gravity current change spins.conf to have:

pyc_loc = -0.2
H1 = -1.0
H2 = 0.0

This will move the pycnocline below the bottom boundary, set the mode-1 amplitude to result in a region of high density at on end of the tank, and give no mode-2 contribution.

Try it yourself. See what each parameter does when they're changed.

Part 2: Matlab driver scripts

Part 2 and 3 extend the previous tutorial. In the remaining sections of this tutorial you will:

1. use a text file specifying parameters for a selection of cases to automatically set up the cases and submit them all to the compute canada scheduler.
2. use the matlab script `spins_refinement.m` to refine the grid for one of the above cases and restart the simulation at higher resolution from a specified timestep.

Setup

To get started on these parts, clone the SPINS refinement git repo. Copy the contents of the tutorial/ directory into the working directory you have been running SPINS from in the previous part.

This directory contains all the files needed to run an already designed selection of cases with no modification necessary.

Run

The workflow for using these scripts is illustrated in the workflow diagram below. Here you will walk through the process.

As mentioned above, some interesting parameters to change are H1, L1, H2, L2, and pyc_loc. The text file `mode1_mode2.txt` controls the cases we will run. Open this file and look at its contents. There are 5 cases, each with a different set of parameters:

1. base. This is the base case, with the default parameters as in the original spins.conf file for this tutorial.
2. mode1. This case changes the mode 2 amplitude and length to 0, meaning we will only have a mode 1 wave propagating to the right.
3. mode2. This case changes the mode 1 amplitude and length to 0, meaning we will only have a mode 2 wave propagating to the right.
4. gravity. This cases uses the parameters as described above to create a gravity current.
5. lamp. This cases increases the height and width of the mode 1 and mode 2 regions to create larger amplitude waves. The pycnocline is also set to be in the middle of the tank.

The matlab script driver_mode1_mode2.m sets up the cases. It creates directories for each case (named according to the casename), writes the parameters to a new spins.conf file, and creates the initial u, v, w, and rho files. This script has its own documentation on the git repository, and the code is well commented.

Now we actually run these cases.

First, open matlab and run driver_mode1_mode2.m to set up the cases. For now, look in each directory it created so you can see what it put in each directory.

Now, submit the matlab.sh script to the scheduler (sbatch matlab.sh). This job runs wavereader.x for each case, and submits a job for each case. Specifically, it submits the submit.sh script from each case directory.